Citation: |
Mengting Jiang, Yuling Liu, Haobo Yuan, Guodong Chen, Weijuan Liu. Evaluation of planarization performance for a novel alkaline copper slurry under a low abrasive concentration[J]. Journal of Semiconductors, 2014, 35(11): 116002. doi: 10.1088/1674-4926/35/11/116002
M T Jiang, Y L Liu, H B Yuan, G D Chen, W J Liu. Evaluation of planarization performance for a novel alkaline copper slurry under a low abrasive concentration[J]. J. Semicond., 2014, 35(11): 116002. doi: 10.1088/1674-4926/35/11/116002.
Export: BibTex EndNote
|
Evaluation of planarization performance for a novel alkaline copper slurry under a low abrasive concentration
doi: 10.1088/1674-4926/35/11/116002
More Information-
Abstract
A novel alkaline copper slurry that possesses a relatively high planarization performance is investigated under a low abrasive concentration. Based on the action mechanism of CMP, the feasibility of using one type of slurry in copper bulk elimination process and residual copper elimination process, with different process parameters, was analyzed. In addition, we investigated the regular change of abrasive concentration effect on copper and tantalum removal rate and within wafer non-uniformity (WIWNU) in CMP process. When the abrasive concentration is 3 wt%, in bulk elimination process, the copper removal rate achieves 6125 Å/min, while WIWNU is 3.5%, simultaneously. In residual copper elimination process, the copper removal rate is approximately 2700 Å/min, while WIWNU is 2.8%. Nevertheless, the tantalum removal rate is 0 Å/min, which indicates that barrier layer isn't eliminated in residual copper elimination process. The planarization experimental results show that an excellent planarization performance is obtained with a relatively high copper removal rate in bulk elimination process. Meanwhile, after residual copper elimination process, the dishing value increased inconspicuously, in a controllable range, and the wafer surface roughness is only 0.326 nm (sq < 1 nm) after polishing. By comparison, the planarization performance and surface quality of alkaline slurry show almost no major differences with two kinds of commercial acid slurries after polishing. All experimental results are conducive to research and improvement of alkaline slurry in the future. -
References
[1] Pandija S, Roy D, Babu S V. Achievement of high planarization efficiency in CMP of copper at a reduced down pressure. Microelectron Eng, 2009, 86(3):367 doi: 10.1016/j.mee.2008.11.047[2] Zantye P B, Kumar A, Sikdar A K. Chemical mechanical planarization for microelectronics application. Mater Sci Eng, 2004, 45:89 doi: 10.1016/j.mser.2004.06.002[3] Fayolle M, Romagna F. Copper CMP evaluation:planarization issues. Microelectron Eng 1997, 37/38:135 doi: 10.1016/S0167-9317(97)00104-4[4] Wang C W, Gao J J, Tian J Y, et al. Chemical mechanical planarization of barrier layers by using a weakly alkaline slurry. Microelectron Eng, 2013, 108:71 doi: 10.1016/j.mee.2013.04.001[5] Wang C W, Liu Y L, Niu X H, et al. An advanced alkaline slurry for barrier chemical mechanical planarization on patterned wafers. Journal of Semiconductors, 2012, 33(4):046001 doi: 10.1088/1674-4926/33/4/046001[6] Murata J, Sadakuni S, Okamoto T, et al. Structural and chemical characteristics of atomically smooth GaN surfaces prepared by abrasive-free polishing with Pt catalyst. J Cryst Growth, 2012, 349:83 doi: 10.1016/j.jcrysgro.2012.04.007[7] Li Y, Liu Y L, Niu X H, et al. Application of a macromolecular chelating agent in chemical mechanical polishing of copper film under the condition of low pressure and low abrasive concentration. Journal of Semiconductors, 2014, 35(1):016001 doi: 10.1088/1674-4926/35/1/016001[8] Zhang W, Lu X C, Liu Y H, et al. Inhibitors for organic phosphonic acid system abrasive free polishing of Cu. Appl Surf Sci, 2009, 255:4114 doi: 10.1016/j.apsusc.2008.10.096[9] Pandija S, Roy D, Babu S V. Chemical mechanical planarization of copper using abrasive-free solutions of oxalic acid and hydrogen peroxide. Mater Chem Phys, 2007, 102(2/3):144[10] Zhang W, Lu X C, Liu Y H, et al. Effect of pH on material removal rate of Cu in abrasive-free polishing. J Electrochem Soc, 2009, 156(3):176[11] Lee H, Park B, Jeong H. Mechanical effect of process condition and abrasive concentration on material removal rate profile in copper chemical mechanical planarization. J Mater Processing Technol, 2009, 209(4):1729 doi: 10.1016/j.jmatprotec.2008.04.021[12] Nguyen V, Vankranenburg H, Woerlee P. Dependency of dishing on polish time and slurry chemistry in Cu CMP. Microelectron Eng, 2000, 50:403 doi: 10.1016/S0167-9317(99)00308-1[13] Yin K D, Wang S L, Liu Y L, et al. Evaluation of planarization capability of copper slurry in the CMP process. Journal of Semiconductors, 2013, 34(3):036002 doi: 10.1088/1674-4926/34/3/036002 -
Proportional views